Projects

Year / Location

Project Type

Project Details

• Design of B.T. Vent Door
• Bill of Material

• Structural Analysis of E-Houses
• Air Cooling Calculation for E-House
• Illuminance Calculations for E-House

• GA Update showing Scrubber & Panama Modification Mooring fittings

• Preparation of Spool Lifting analysis 18" spool at HAS Platform at Tie in point 1
• Preparation of Spool Lifting analysis 18" spool at HAS Platform at Tie in point 2

• Preparation of Spool Lifting analysis 14" spool at HAS Platform at Tie in point 1
• Preparation of Spool Lifting analysis 14" spool at HAS Platform at Tie in point 2

• Lifting Analysis of Protection cage for 10" B-147A to tie-in at hot tap
• Preparation of Lifting Analysis report.
• Preparation of Rigging Drawing.

• Crane chart for MV Seamec Princess cranes from crane rating sheet.
• Lifting plan using the MV Seamec Princess crane for "hot tap cage protector"

• Software for Intact stability, Damage stability and Longitudinal strength modules of Stability Instrument for the subject vessel

• Design and calculation of additional funnel structure.

• Study of the regulatory and technical compliance of vessel to carry out required operations
• Equipment [Crane] – study of outreach to install structure at locations and lifting capacity to support the payload
• Structure [Deck Strength] – study of load bearing capacity of the cargo deck to support the maximum weight of payload
• Stability [Heel/Trim] – anti rolling check of vessel during crane operation using the load cases defined in stability booklet.

• Mooring Fittings Upgrade for M.V. Gaia Celeris as Per Pilbara Ports Authority (PPA)
• Updated General Arrangement drawing for PPA's Ship Towing
• Updated Mooring Arrangement drawing for PPA's Ship Towing (SWL 125 tons)
• Underdeck Stiffening drawings for New Mooring Fittings
• Bill of Material for underdeck Stiffening.
• Strength calculation of underdeck reinforcement for New Mooring Fittings

• Drawing Preparation of Rigging Arrangement and Analysis of 1 spool based on lifting analysis, 12" - NLM12, Tandem Lift
• Preparation of Lifting Analysis & Lifting Arrangement Report

• Drawing Preparation of Rigging Arrangement and Analysis of 1 spool based on lifting analysis (NLM-13 to NLG at NLM-13)
• Preparation of Lifting Analysis & Lifting Arrangement Report

• Pilot Shelter Detail
• General Arrangement showing the position of pilot shelter with the pilot ladder arrangement

• Preparation of Lifting Analysis report as per provided rigging arrangement

• Pre bid engineering study for conversion of PSV Nalanda from ERRV Group (C) to ERRV Group (B) Compliance.
• Estimation of major equipment and materials requirements.

• Survey of under construction Jack Up Barge to ascertain percentage and quality of work done.

• Compliance survey of vessel to meet technical specifications

• Side shell & webs were damage due to collision with jetty, structure repair plan was prepared as per IACS standard.

• Cracks were observed on web frame 35, repair plan was prepared.

• Prewash calculations by forced air ventilation for noxious cargo tanker & addendum to P&A manual

• Prewash calculations by forced air ventilation for noxious cargo tanker

• Design of BOP bonnet handling system foundation frame.
• Analysis & design of roughneck support structure

• Design of A-frame and lifting barge for installation of bridge span across Narmada River.

• Structural modelling of existing tanker
• Structural modelling of modifications to suit FPSO service
• Design and Modelling for Piping / HVAC / Piping support
• Detailed engineering for Electrical and instrumentation – IO List, instrument index, block diagrams, cable tray layouts, etc.
• Detailed engineering for material handling
• Equipment data review
• Process safety
• Basic design of major structural outfits – helideck, crane, foundations of offloading hose reel, and various miscellaneous equipment
• General arrangements and isometrics

• Preparation of Docking Plan
• Technical liaising with Class for approval

• Renewal of various steel structures of the Rig Actinia

• Preparation of 2D drawings for transportation of various cargoes
• Lashing and loadout calculations

• Design & analysis of mooring system to meet operating and survival conditions
• Structural Analysis and design of under deck strengthening for chain stoppers
• Preparation of under deck strengthening drawings for chain stopper
• CAPEX study for complete conversion
• Study of site data
• Technical liaisoning with Class

• Modeling of Beam Elements, rigid connections and support constraints, spring elements etc.
• DNV code, Marine Operations part 2, Chapter 5 Lifting.
• Preparation of lifting arrangement drawings.

• Feasibility Study for 60 Tons crane Installation
• Feasibility Study for 8 Tons crane relocation
• Feasibility for 10 Tons crane installation
• Stability analysis with new crane arrangements

• Preparation of Crane pedestal foundation dwgs
• Structural strength analysis iwo crane installation
• Preparation of Structural modification plan
• Stability Analysis
• On site Inclining experiment

• Digitization of existing drawings
• Structural analysis of area of concern for crop and renewal
• Preparation of strengthening drawings and analysis report

• Digitization of existing drawings
• Structural analysis of under deck container footings
• Preparation of strengthening drawings

• Structural analysis of Helideck
• Renewal methodology

• Structural analysis of sand trap support structure
• Renewal methodology

• Design and analysis of swing platforms

• Structural analysis of windlass foundation
• Renewal methodology

• Design and preparation of fabrication drawing for sewage tank

• First principle analysis to renew the corroded part of column shell to meet ABS recommendation

• Installation of AC unit to augment the existing AC system
• Preparation of structural and piping drawings

• Design of bomb shelters for drill floor

• Design of base platform for tugger winches to assist handling of drill strand

• Eight point mooring analysis of rig actinia at 35m water depth for operating and survival condition

• Mooring analysis of bunker tanker to single buoy system
• Design of gravity anchors

• Mooring analysis of vessel “Kreuz Supporter” for operating and survival condition in Mumbai high oil field
• Catenary plots for understanding the vertical clearances from subsea pipelines

• Mooring analysis of vessel “Kreuz Supporter” for operating and survival condition in Tapti oil field
• Catenary plots for understanding the vertical clearances from subsea pipelines

• Under deck strengthening assessment for higher capacity, proposal of suitable additional strengthening
• Analysis of crane knuckle boom for higher capacity

• Installation drawings for 150 t crane
• Structural assessment
• Stability assessment

• Preparation of statutory layouts
• Preparation of system layouts

• Preparation of system drawing
• Heat calculation
• Layout drawings

2015-India

DP capability Plot

• Preparation of Dp capability plot and thrust Utilisation curves
• Evaluation under operating and survival condition

2015-India Ongoing

Peer Review of Mooring Analysis report.

• Peer Review of Mooring Analysis report for accommodation barge.
• Review of Analysis methodology, system particulars, met-ocean data etc.
• Field layout review,
• Review of analysis results against design criteria (acceptance criteria) based on expertise and detailed mooring analysis (if required).
• Issue of recommendations.

2014 – India – Ongoing

Design and Installation of lifting beams on Semi Submersible- Actinia

• Preparation of Structural Drawing
• Structural Calculation

2014-India Ongoing

Review of Baseline Platform Inspection Report (BPI) & Marine Growth Review (MGR) Report

• Review of BPI-MGR report for recertification of jacket platform
• Review of previous certification recommendation and outstanding activities
• Review of periodic inspection, damages reported and remedial works completed
• Assessment of the condition of the Jacket structure with respect to the as-built data
• Issue of recommendations

2013 Abu Dhabi

BUNDUQ HSE Management System Manual update

• Assisting DNV for BUNDUQ’s HSE Management System Manual update

2013 Abu Dhabi

OOCEP Corporate HSE Training Procedure

• Assisting DNV for preparing OOCEP’s Corporate HSE Training Procedure

2013
Abu Dhabi

BUNDUQ HSE Management System Manual update

• Assisting DNV for BUNDUQ’s HSE Management System Manual update

2013
Abu Dhabi

OOCEP Corporate HSE Training Procedure

• Assisting DNV for preparing OOCEP’s Corporate HSE Training Procedure

2012-India

Windload Analysis for CPC Zapata

• Evaluation of windload and wind heeling moment on vessel and crane being carried piggy back
• Determin critical wind speed and direction to limit operations envelope

2012-Abu Dhabi / India

GASCO ASAB – III, Phase – 3, EIA

• Assisting DNV for ASAB – III, Phase – 3, Environmental Impacy Analysis (EIA) Study

2012-Abu Dhabi / India

ADCO-TR Full Field Development HSEIA – Phase IV (Decommissioning & Demolition) Study

• Assisting DNV for ADCO-TR Full Field Development Health, Safety & Environmental Impact Assessment (HSEIA) – Phase IV (Decommissioning & Demolition) Study

2012-Singapore

Hydrodynamic Analysis for 88m PSV

• Calculation of extreme sea motions at cranes and vessel CG points under sea conditions given by the owners

2012-Singapore

Pre Bid Engineering Assistance for Martin Linge FSO for  Hild Field

• Engineering assistance for hull structure modification
• F.E.A. for hull structure
• Review of hull and marine system drawings

2012-India

Pre Bid Engineering Assistance for Modification to ONGC Oil Rig

• Engineering assistance for hull structure modification
• Review of hull and marine system drawings

2011- Singapore

Modification to LNG Vessel Cargo Piping

• Modification of Piping
• Design of New Production Manifold
• HAZOP Study for above modification

2011-Abu Dhabi

ADGDC Drilling Safety Manual

• Assisting DNV for ADGDC Drilling Safety Manual

2011-Abu Dhabi

ZADCO Incident Reporting & Investigation Procedure

• Assisting DNV for ZADCO Incident Reporting & Investigation Procedure

2011-Singapore

Sea keeping and hydrodynamic analysis of offshore vessel

• Calculation of extreme sea motions at cranes and vessel CG points under sea conditions given by the owners

2011-Singapore

Gob Eye structure design

• Finite element analysis of gob eye structure

2010-Oman

Petroleum Development Oman (PDO) - Asset Integrity Process Safety Management Assessment

• Assisting DNV for preparation of PDO Asset Integrity Process Safety Management Assessmentfor onshore drilling operations.

2010-Singapore

Structural analysis for Cattle carrier generator installation

• Finite element analysis
• Strength and vibration calculation
• Generator room design

2010-Singapore

FPSO Marine Systems

• Engineering and Drawing for De-commissioning FPSO systems.

2009-Singapore

Helideck Design Analysis

• Engineering and Structural Analysis for Helideck retrofit on an oil platform

2009-Singapore

Fitment of Gondola, transducers and trolley and Moon Pool

• Engineering and structural analysis for Fitment of Gondola, transducers, trolley and Moon Pool on board seismic survey vessel

2008-Singapore

Global FEA for FPSO,  Design of module Stool Supports and Crane Pedestal with Boom Rest

Global 3-D Finite Element Analysis

• Dynamic loads
• Internal loads for cargo conditions
• Turret mooring reactions
• Turret loads on deck

Deflections and stresses for:

• Helideck
• Flare Tower
• Topside stools
• Coarse & Fine Mesh Modeling
• Crane Pedestal with Boom Rest

2007-Singapore

Vibration Analysis for TG Foundation

• Structural design of the Turbine Alternator    Foundation
• Static analysis of the deck structure
• Evaluation the natural frequency of the engine room deck structure
• Vibration study and the foundation drawing

2007-Singapore

Preliminary Mooring Analysis

• 8 point spread moored system
• Dynamic spread moorings analysis according to class requirement including intact, damage and transient cases.
• Simulated load results.
• Mooring pattern
• Cantenary plot
• Motion envelopes
• Anchor type evaluations

2007-Singapore

Hydrodynamic design for FSO

• Green water analysis
• Slamming analysis
• Air gap analysis for external turret

2006-Singapore

Upgrade design and systems engineering
(1 x FPSO 59,650 tdw)

• Location analysis / spread mooring analysis
• Offloading analysis
• Hull analysis
• Evaluation of marine systems

2006-Singapore

Steel renewal
(1 x FPSO 59,650 tdw)

• Shipyard supervision of steel renewal

2006-Singapore / Malaysia

Conversion of 1 x chemical tanker to FPSO

• Complete preliminary design and engineering for bid process
• Hull evaluation for ultimate limit states

2006 - Singapore / Malaysia

Conversion of 2 Panamax hulls to FPSOs

• Complete preliminary design and engineering for bid process
• Hull evaluation for ultimate limit states
• Systems engineering and integration of process plant and topsides
• Preparation of tender documents for submission

2006-Singapore / Malaysia

Conversion of Suezmax tanker to FPSO

• Complete preliminary design and engineering for bid process
• Hull evaluation for ultimate limit states
• Systems engineering and integration of process plant and topsides
• Preparation of tender documents for submission to oil major.